Topic: ultraviolet light from LEDs

Technology with benefits: ultraviolet light from semiconductor LEDs

A great variety of applications, ranging from water disinfection to UV curing, make use of the advantageous properties of ultraviolet (UV) light. Until recently, the generation of ultraviolet light was limited to conventional sources such as mercury gas discharge lamps. However, modern semiconductor-based UV light emitting diodes (LEDs) can outperform these conventional sources in many respects: Rather than emitting a limited number of discrete wavelength lines given by the respective gas molecules, the spectrum of a UV LED can be freely adjusted by the semiconductor alloy composition. In addition, toxic substances like mercury are replaced by environmentally friendly group-III nitride semiconductors. Last but not least, UV LEDs can be turned on and off rapidly; they are fully dimmable, allow efficient heat extraction, and provide a compact form factor. In the long run, UV LEDs are expected to score with long operation lifetimes, a high efficiency, and an attractive pricing. Therefore, their market share is expected to take a leap from about 45 million $US in 2012 to 270 million $US in 2017 – with an annual growth rate predicted to be around 43 % (cf. Yole Développement, March 2013).

Modules designed to fit specific requirements

The FBH has realized several compact UV LED modules, each customized for the specific demands of the application. In collaboration with its partners from universities, other research institutes, and companies, functionality and effectiveness of the modules have been successfully demonstrated. Continuous disinfection of a flow cytometric cell sorter in a medical environment, for example, has been demonstrated. Current development efforts aim at enhancing this approach to clinical applications, such as the therapy of humans suffering from autoimmune disorders. For this purpose, very specific rare cells shall be isolated from the human body; they can then be grown in vitro in large quantity and returned to the patient to treat the disease. In further experiments, the concentration of secondary metabolites in plants could be significantly enhanced by illumination with UV LEDs – an effect which may be used to grow vegetables enriched with specific human-protective secondary metabolites for functional foods and nutraceuticals.

Full technology chain

FBH has developed epitaxial growth processes and chip fabrication technologies to realize UV LEDs emitting in the spectral range between 380 nm and 235 nm. The technology involves the full process chain including metal organic vapor phase epitaxy (MOVPE), LED chip processing, and flip-chip mounting up to the assembly of complete UV LED modules. This also comprises modeling of heterostructure designs and simulation of the device characteristics at all process stages. FBH has developed, for example, focusable LEDs emitting in the spectral range around 365 nm with very small emitting areas. Due to the special chip design, closely resembling point sources, the UV light can be easily coupled into optical fibers – a key feature particularly for mobile applications such as battery-powered devices used for in situ blood gas sensing.

Further information regarding FBH's UV LEDs.


M. Kneissl, T. Kolbe, C. Chua, V. Kueller, N. Lobo, J. Stellmach, A. Knauer, H. Rodriguez, S. Einfeldt, Z. Yang, N.M. Johnson, M. Weyers, "Advances in group III-nitride-based deep UV light-emitting diode technology", Semicond. Sci. Technol., vol. 26, no. 014036 (2011).

light spectrum ([M] FBH: ©Horst Frank/Phrood/Anony, CC BY-Sa 3.0)

About ultraviolet light – and its applications

Visible light covers the wavelength range from about 780 nm in the red down to 380 nm in the violet. The invisible ultraviolet (UV) light, however, is electromagnetic radiation at shorter wavelengths, distinguished in near UV (UV-A, 380 – 320 nm), mid UV (UV-B, 320 – 280 nm), and deep UV (UV-C, 280 – 100 nm). The sun is a natural UV source, though hardly utilizable for commercial applications, since water vapor, ozone, and oxygen naturally occurring in the atmosphere absorb a significant portion of the UV-B and UV-C radiation.

However, UV light can be generated technically and used in many ways: Organic and inorganic compounds, for example, undergo various chemical reactions when subjected to UV light. Exposing polymers to ultraviolet light results in cross-linking of molecule chains which hardens and solidifies the material. UV light can break chemical bonds in the DNA strands and hence suppress the replication of micro-organisms – a key process in water disinfection. In addition, UV light can be used for the treatment of skin diseases, for the detection of fluorescence markers as well as for sensing of various gases and liquids.

Novel approaches to disinfect water with UV LEDs

UV-A LED module for photocatalysis
Rod-like UV-A LED module for TiO2 photocatalysis
principle flow cytometry
Principle of flow cytometric cell sorter with integrated UV-C LED module
degradation methylene blue
Degradation rate of methylene blue by a TiO2 layer actived with UV-A LEDs

Two different disinfection processes for water and further liquids can be triggered by UV radiation. Firstly, the well-established direct destruction of DNA with deep UV radiation in the wavelength range between 220 nm and 280 nm. Secondly, the decomposition of organic compounds solved in water using TiO2 photocatalysis excited by near UV light with a wavelength around 360 nm. Currently, mercury gas discharge lamps are used for such processes. Since several years, UV LEDs have increasingly attracted interest as alternative UV radiation sources. Main advantages are their tailored wavelength, long lifetime, compact form factor, and low operation voltage. At the FBH, several modules and systems have been realized efficiently using the emitted UV radiation and thus bringing UV LED technology into new applications.

Clever disinfection – extending maintenance cycles of medical equipment

Irradiation in the deep UV range is an effective way to prevent microorganisms from reproduction. Since LED efficiency has been constantly improved in recent years, they can already be used for liquids with low flow rates in the order of a few liters per minute. Accordingly, the FBH has developed a water disinfection module and implemented it into a flow cytometric cell sorter, an equipment used to count, identify, and sort human cells. The module allows reducing the number of microorganisms in the carrier fluid by up to three orders of magnitude. Before, costly and labor-intensive chemical sterilization processes had to be performed every day. With the UV LED module emitting around 280 nm, the cell sorter remains sterile for at least seven days after system sterilization without any chemical cleaning. The module has been developed in close collaboration with Technische Universität Berlin and is currently being tested in flow cytometers at German Rheumatism Research Centre Berlin.

Photocatalysis – efficient activation of surfaces

Substances that are difficult to degrade, including medication, chemicals, and organic compounds, can be efficiently decomposed by TiO2 photocatalysis. Applications for the process range from house paints to medical surfaces. To benefit from the self-cleaning and antimicrobial effect even in small and geometrically complex constructions, compact UV LEDs are an attractive option. They additionally promise to be particularly efficient since the wavelength can be adjusted precisely to the absorption spectrum of TiO2. In the joint research project "NanoPurification", for example, a novel rod-like UV LED module has been developed as radiation source for TiO2 photocatalysis in water treatment reactors. The module design was particularly optimized in terms of high density packaging of the UV LEDs, effective thermal management, and modular expandability. This design enables sufficiently high UV irradiance at a wavelength of 360 nm and flexible adaption to different reactor geometries. Efficient heat dissipation of the thermal power loss from the UV LEDs is particularly important, because low temperatures is one key to long operation lifetimes as well as constant emission wavelength and optical power. The photocatalytic efficiency of the system has been demonstrated by determining the degradation rate of methylene blue, a stain to highlight structures in biological tissues. For this purpose, a TiO2 layer, activated by the emission from the UV LED module, was used resulting in a degradation rate of ≥ 20 %/h at an irradiance of 150 W/m2.


M. Kneissl, T. Kaiser, T. Kolbe, "UV-C LED disinfection module for flow cytometry and sterile cell sorting by using a UV-C LED disinfection module", U.S. Patent Application 61/451,796.


M.A. Würtele, T. Kolbe, M. Lipsz, A. Külberg, M. Weyers, M. Kneissl, M. Jekel, "Application of GaN-based ultraviolet-C light emitting diodes - UV LEDs - for water disinfection", Water Research, vol. 45, no. 3, pp. 1481-1489 (2011).

Surface treatment by UV light – high-power LEDs on the rise

UV LEDs from the FBH on different submounts
MOVPE for GaN epitaxy
Multi-wafer reactor at FBH for metal organic vapor phase epitaxy of GaN

UV-B LEDs emitting in the wavelength range from 280 to 320 nm are ideally suited for surface treatment of polymers, resist curing, hardening of paints, plant growth lighting, and phototherapy. However, the usage of these devices is hampered by the large optical power required for many of these applications. Within the "Berlin WideBaSe" network, the FBH and its partners have developed flip-chip mounted bottom-emitting UV-B LEDs that deliver a high optical output power of more than 13 mW at high currents. Moreover, the devices show long operation lifetimes – more than 1,000 hours under continuous-wave operation at room temperature. A loss in optical power occurs mainly during the first 50 hours; further degradation is slow even for operation currents as large as 300 mA. These results significantly exceed commercially available UV-B LEDs which are typically specified for operation at a low current of 20 mA.

Mastering technological challenges

To achieve these performances, many technological obstacles had to be overcome. With respect to material growth, the epitaxial layer structures were optimized in terms of optimum current injection into the active region of the heterostructure. For instance, an optimized electron blocking layer was developed minimizing the overflow of electrons beyond the active region. Moreover, the density of extended crystal defects was reduced by utilizing sophisticated concepts of AlGaN buffer layers deposited on sapphire substrates and applying the concept of epitaxial lateral overgrowth (ELO), respectively. This way, the internal quantum efficiency of radiative carrier recombination has been significantly enhanced. A large effort was also devoted to optimizing the chip design and fabrication process in order to achieve uniform light emission, to increase light extraction efficiency, and to obtain efficient heat dissipation. For instance, special micro-LED arrays with segmented electrical contacts were developed both to reduce current crowding and to increase heat extraction. Moreover, the metallization schemes for ohmic electrical contacts on n-type AlGaN were optimized by using, for example, novel elements like vanadium, resulting in a significantly reduced operation voltage of the LED. Finally, two concepts to increase the efficiency of extracting UV light from the LED chip have been developed: nanopixel p-contacts combined with an aluminum UV reflector and sapphire substrates textured with micro-optics. After laser scribing the LED wafers are diced into LED chips and then hard-soldered onto AlN ceramic submounts, ensuring a low thermal resistivity of the package.

Further information:


N. Lobo Ploch, H. Rodriguez, C. Stölmacker, M. Hoppe, M. Lapeyrade, J. Stellmach, F. Mehnke, T. Wernicke, A. Knauer, V. Kueller, M. Weyers, S. Einfeldt, M. Kneissl, "Effective Thermal Management in Ultraviolet Light Emitting Diodes with Micro-LED Arrays", IEEE Trans Electron Devices, Vol. 60 (2) 782-786 (2013).

M. Lapeyrade, A. Muhin, S. Einfeldt, U. Zeimer, A. Mogilatenko, M. Weyers, M. Kneissl, "Electrical properties and microstructure of vanadium-based contacts on ICP plasma etched n-type AlGaN:Si and GaN:Si surfaces", Semicond. Sci. Technol., vol. 28, no. 125015 (2013).

T. Kolbe, F. Mehnke, M. Guttmann, C. Kuhn, J. Rass, T. Wernicke, M. Kneissl, "Improved injection efficiency in 290nm light emitting diodes with Al(Ga)N electron blocking heterostructure", Appl. Phys. Lett., vol. 103, no. 031109 (2013).

ELO – boosting UV LED efficiency

ELO process
Epitaxial lateral overgrowth process at FBH

The efficiency of UV LEDs significantly depends on the crystal quality of the semiconductor heterostructures. These structures are epitaxially grown on sapphire substrates by metal organic vapor phase epitaxy. To improve the crystal quality as well as to reduce the stress in the growing layers, FBH has successfully implemented the method of epitaxial lateral overgrowth (ELO) in LEDs emitting in the UV-B and UV-C range. After the deposition of AlN layers and subsequent structuring into a stripe pattern, AlN growth is continued. As a result, a compact film is formed due to coalescence of the laterally growing stripes. These advanced AlN layers are the basis for subsequent epitaxy of the diode structures.

Further information:

FBH research: "Growth process modification to improve the quality of Al0.45Ga0.55N", no direct link, please scroll to 27.09.2012


V. Kueller, A. Knauer, U. Zeimer, M. Kneissl, M. Weyers, "Controlled coalescence of MOVPE grown AlN during lateral overgrowth", J. Cryst. Growth, vol. 368, pp. 83-86 (2013).

A. Knauer, V. Kueller, U. Zeimer, M. Weyers, C. Reich, M. Kneissl, "AlGaN layer structures for deep UV emitters on laterally overgrown AlN/sapphire templates", phys. stat. sol. (a), vol. 210, no. 3, pp. 451-454 (2013).

U. Zeimer, V. Kueller, A. Knauer, A. Mogilatenko, M. Weyers, M. Kneissl, "High quality AlGaN grown on ELOAlN/sapphire templates", J. Cryst. Growth, vol. 377, pp. 32-36 (2013).

V. Kueller, A. Knauer, C. Reich, A. Mogilatenko, M Weyers, J. Stellmach, T. Wernicke, M. Kneissl, Z. Yang, C.L. Chua, N.M. Johnson, "Modulated Epitaxial Lateral Overgrowth of AlN for Efficient UV LEDs", IEEE Photonics Technol. Lett., vol. 24 , no. 18, pp. 1603-1605 (2012).

Advanced concepts for light extraction

micro-structurs & nanopixel contacts
Light extraction concepts with micro-structures & nanopixel contacts

Light extraction is crucial for the realization of high-efficiency UV LEDs. At the FBH, two novel concepts to enhance light extraction have been developed and successfully implemented into UV LEDs.

  • A general approach, applicable to all LEDs, uses microstructures etched into the backside of the sapphire substrate. Reflection at the additional facets increases the probability of photons to enter the escape cone of the chip and thus enhances the LED efficiency.
  • The concept of nanopixel contacts addresses near-UV LEDs with a UV transparent p-side of the semiconductor. A two-dimensional array of palladium pads of submicrometer size serves as low resistance contact, while the space between the pads is filled with aluminum as a reflector for UV light.


M. Kneissl, M. Weyers, S. Einfeldt, H. Rodriguez, "P-contact and light-emitting diode for the ultraviolet spectral range"
US Patent Application 13/384,208
Europäische Patentanmeldung 10737530.5 - 1226 PCT/EP2010/060333
Deutsche Patentanmeldung 10 2009 034 359.8


N. Lobo, H. Rodriguez, A. Knauer, M. Hoppe, S. Einfeldt, P. Vogt , M. Weyers, M. Kneissl, "Enhancement of light extraction in UV LEDs using nanopixel contact design with Al reflector", Appl. Phys. Lett. 96, 081109 (2010) DOI: 10.1063/1.3334721.